What is a tech pack?
The document a factory actually makes your product from: measurements, materials, construction and finishings, written so that someone who has never spoken to you can make the piece you have in mind.
What a tech pack is
A tech pack · technical pack, technical file, fiche technique · is the complete specification of one product. One product, one document. It travels from you to the workshop, and it is what gets quoted, sampled, corrected and finally made.
It is not a moodboard and it is not a drawing. A moodboard says what the piece should feel like; a tech pack says what it is. The test is simple: could a maker you have never met produce the right piece from this document alone? If the answer needs a phone call, the document is not finished.
Two things follow from that, and they are the whole discipline:
- Every number is a decision you have made · not one the factory will make for you.
- Every version is dated · because the piece you receive will be made from one specific version, and six weeks later nobody remembers which.
What goes inside, page by page
The order below is the one most workshops expect. Names vary by trade; the content does not.
- Global product · front and back, flat, on one page.
- Item description · composition, intent, the notes that do not fit anywhere else.
- Technical drawings · the construction, line by line.
- Details · collar, cuff, pocket, closure, each one enlarged.
- Seams reference · which seam, and where.
- Measurement chart · points, values, tolerances, graded sizes.
- Materials and trims · references, suppliers, consumption.
- Labelling · composition, care, origin.
- Packing and folding · how it leaves the factory.
For jewellery and small leather goods the shape is the same with different sheets: stones and their settings, metal and plating, weights, dimensions, hallmarks, finishing.
A sheet you have nothing to say on is a sheet you remove. An empty page in a technical document reads as an oversight, and an oversight gets filled in by someone else.
Measurements and tolerances
This is where tech packs are won or lost. Three rules carry most of it:
- Name the point, do not describe it. "Chest, 2.5 cm below armhole, measured flat, doubled" is a measurement. "Chest width" is a conversation.
- Give a tolerance. Nothing is made to the millimetre. Without a tolerance you have not specified a range · you have specified a disappointment. ± 0.5 cm on small measurements, ± 1 cm on large ones, is a common starting point.
- Give the graded sizes. One size is a sample. The grading between sizes is a decision, and it belongs to you.
Write the measuring method once, at the top of the chart: flat or on the body, doubled or single, relaxed or stretched. Two people measuring the same garment two different ways will disagree by more than any tolerance you set.
Five mistakes that cost a sampling round
- The same thing said twice, differently. A measurement on the drawing and another in the chart. The workshop picks one · usually not yours.
- Colour by name. "Navy" is not a colour. A reference is: a Pantone code, a dyed swatch, a supplier reference. Send the swatch.
- A material without a reference. "Heavy cotton twill" buys you a fabric you did not choose. Name the mill, the article, the weight.
- Feedback in a message thread. If a correction is not in the document, it is not in the piece. The thread is where it was said; the tech pack is where it lives · our sample feedback template is the format that travels back the other way.
- A version number that means two different things. If V2 is rejected and a corrected V2 arrives, it is V3. Numbers go up, and never reset.
Sending it, and versioning it
Send a PDF. It prints identically everywhere and nobody edits it by mistake. Put the version and the date in the document, on every sheet · the workshop prints it, and a printed page with no version on it is a page nobody can trust two months later.
Keep a record of what changed between versions. Not for bureaucracy: because the one question that always comes back is "did they get the new sleeve length or the old one?", and the answer should be a fact, not a memory.
The tech pack is one half of the loop with a workshop; the samples that come back are the other. Managing samples and prototypes covers naming versions and writing feedback a factory can act on.
Doing it in Teseo
Teseo has a tech pack editor built for exactly this document · and for the moment after it, which most tools forget: sending it, and knowing which version the workshop has.
- A real sheet, not a form. You work on A4 pages: text, photographs, arrows, measurement callouts, drawings. A garment template opens with its sheets already in place; a free sheet stays empty for anything that does not fit a template.
- It fills itself from your product. Link the tech pack to a product record and the header · reference, season, category, designer · stops being retyped.
- It leaves as a PDF, A4 landscape, exactly what you see on screen.
- Or as editable SVG, which your studio opens in Illustrator with the text still text and the drawings still drawings. One file per page, so a ten-page pack arrives as ten A4 artboards rather than one enormous image.
- It goes to the workshop from Teseo. Pick a supplier, tick the packs, check each PDF before it leaves, send. Each send is recorded with its version.
- Your old packs still count. Bring in a PDF you already have and each page becomes a sheet you can annotate and build on.
Write the document the workshop needs
Measurements, materials, construction and finishings on real A4 sheets · linked to your product record, exported as PDF or editable SVG, and sent to your supplier with its version attached.
Questions
Do I need a tech pack for a first small run?
Yes, and more than for a large one. A big factory has a pattern room that will catch your omissions. A small workshop taking twenty pieces will make exactly what the document says, and invoice you for the version you did not ask for. The document is what makes a quote comparable between two makers.
What file should I send?
PDF, every time. It opens everywhere, it prints the same everywhere, and it cannot be edited by accident. Send a vector file as well only if your maker has asked for one · most do not want it, and the ones who do will tell you.
Who writes it, the designer or the factory?
You write it. A factory that offers to "do the tech pack for you" is offering to decide, on your behalf, everything you did not specify · and those decisions become the piece. Their pattern maker may redraw your pattern, which is normal and useful. The intent stays yours.
How detailed is too detailed?
There is no such thing as too precise on measurements, materials and finishings. There is such a thing as too many pages · a thirty-page document gets skimmed. Say each thing once, in the place where it belongs, and never twice with two different numbers.
What about my old tech packs, made elsewhere?
Keep them. A PDF you already have can be brought into Teseo and each of its pages becomes a sheet you can annotate, measure and build on. ⚠ It arrives as the page image, not as editable text · you continue on top of it rather than rewriting it.